3 Ply Automatic Corrugated Cardboard Production Line

3 PLY CORRUGATED CARDBOARD PRODUCTION ong>main technical parameters and requirements in production n>

note:Production d test paper should meet the following requirements:(the surface temperature of the equipment is not less than 172ºC)Paper rating of not less than B grade Paper moisture content of about:11%±2%top paper:100-250g/m2 core paper:100--250g/m2corrugated paper:100-200g/m2

amount of steam 2500-3000Kg/Hr the highest pressure:1.2MPacommon pressure:0.8-1.1MPa 6,power supply:380V 50Hz Three-se four-pan> 7,equipment installed total power:about120Kw The actual power consumption:about 60Kw(full speed) 8,equipment covers:about38m×10m×5m(Specific length of foundation Figure prevail) 9,Equipment out of paper orientation:According to the user to determine the transmission plant set left or right position 10,Equipment applicability,Available in A, B, C class domestic or imported paper PaperCustomer-owned section1,steam heating system:proposal with 2000Kg / Hr of a steam boiler pressure:1.25MPa steam pipean>2,air compressed machine,air pipe conveying pipe.3,power supply,d to the operation panel and .4,water sources,water pipekets and so on.5,Water, electricity, gas flush mounting civil foundation.6,Test with the base paper,corn starch (potato),Industrial use caustic soda,borax and other material.7,Oil equipment,lubricating oil,hydraulic oil,lubricating grease.8,installation,commissioning of food, accommodation.And provide installers with the installation.

ZJ-F shaftless mill roll standStructural features:1.Symmetrical structure can also install two bundles of paper at the same time,Paper can be used for non-stop for a job;Adopts mechanical drive to complete the paper clamping, lifting, loosen, move on, around translational motion, etc.2.each shaftless mill roll stand is equipped with two pieces of paper guide, two set of paper car;paper guide the use of channel 14 and the guide post weld,paper car adopt 10mmwelded stell,the length of track is 4500mm.3.manual dics brake,add screw following4.electric zed control the electric huck.technical parameters:1,Backstands action mode:mechanical electric operation2,the range of paper jams:maximum:1800mm minimum:600mm3,the diameter of paper jams:maximum:¢1400mm minimum:¢400mm4,Unilateral maximum load:maximum2000Kg5,Powered motor parameters:A Paper jams motor550W×4set 380V 50HZ short(S2)working standardB lift motor 1.5Kw 380V 50HZ short(S2)working standard

RG-1-600 top(core)paper preheaterStructural features:

1. In accordance with national standard category pressure vessel,and with the pressure vessel certificate.

2. The roll surface after precision grinding, fine grinding and hard chromium plating processing,surface friction,durable.

3. electric adjustable angle, angle can rotate in the range of 360°,and adjust the paper preheat area.

SF-280S fingerless type single facerStructural features:

1. adopt hood suction structure，matched high pressure powerful fan. Gas supply and electrical control cabinet to focus on the same operation, the operating side full cover closed.

2. High quality resin sand casting，wall thickness 200mm。Adopt independent gear box, Universal joint transmission structure.

3. install the lifting trolley on the conveyor bridge,Need to use the car will tile roll assembly and pressure roller, such as convenient and quick.

4. Glue roller unit structure with the overall relocation，Maintenance can sway the machine at the overall maintenance，improve the working efficiency。

5. The humidity control apparatus equipped with a spray, so flute type to maintain good stability of deformation, avoid dry。

6. Automatic circulation system for glue, two-cylinder pneumatic gluing device, with good cushioning effect.

RG-2-600 triple preheaterStructural features:1. preheat roller accord with the national standard of the pressure vessal,and enclosed the pressure container certificate and inspection certificate.2. Each roller surface after grinding precision grinding and dealing with hard chrome plating, Surface friction is small, durable.3Electric adjustable angle, it can rotated adjust the paper preheat area in the range of 360°.GM-12 double glue machineStructural features:1. After the glue roller surface after quenching inner hole machining, grinding and dynamic balancing surface engraved with pit style textured, coating evenly, less consumption of plastic.2. doctor roller surface by grinding and hard chromium plating.3. other guide rollers with hard chrome plated.4. Pressure roller with pneumatic lift, easy operation.5. manually adjust scraping gap.6. glue roller ¢ 215mm,Doctor roll¢ 122mm,press paper roller¢ 122mm,preheat roller 270mm.7. Electrical design, construction production process, follow the national standards, low failure rate, easy maintenance.SM-10 type double facerStructural features:1. Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m. Heating plate with a container board production, in national standards for a class pressure vessel, with pressure vessel certificate and inspection certificate.2. Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.3. Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.4. on cotton use two-cylinder S type cotton belt with the tensioning device.5. lower belt adopt pneumatic tensioning.6. Drive roller coated with attached wear-resistant rubber ,showed a herringbone structure,With a high, ensure smooth cardboard output.7. Main drive motor for frequency conversion motor,low-speed torque,wide speed range ,reliable, and easy maintenance.8. hot plate internal for partition isolation structure,s-shaped flow of steam,Steam, water separation function significantly improves the utilization of steam.ZQS thin knife slittingstructural feature:1. Overcome the conventional type of pole, cutting pressure ear when collapsed cardboard cut nomenon, cutting board smooth, quality has improved significantly.2. the whole machine can remove left and right,cycloid reducer to adjust.3. Cutter and easy to adjust the pressure error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other features.4. the machine adopt five knives eight blade is made of tungsten alloy steel, the using life is not less than 3 million running meters.NC-120 NC cutter helical knivesstructural feature:1 .it can store 200 units orders,replace the cutter specifications quickly and accurately,changing orders without stop,And enables networked computers to facilitate production management.2. Knife shaft drive gears are precision forged steel induction hardening, backlash-free transmission, advanced keyless connection, high transmission accuracy.3. Cutting machine adopts inlaid front steel blade knife spiral structure, serrated knife. scissors, shears, shear force, long blade life.4. around feed rollers are used the sun gear platen way, smooth delivery, pressure evenly, easy to crush plate board or cause blockage.5. Exact and adjustable no gap gear to ensure precise blade engagement, running balance.6. Knife roller: fine quality forged steel material, the balanced, with good stability.7. Germany Bryant servo motor drive controller, Taiwan Eview yield 10.4 inches color touch screen display, the project at a glance.8. Cutting length: 500mm-9000mm, cutting precision: ± 1mm (at steady speed).DMT-120 paper sheet delivery and side conveyorstructural features:1.Adopted on the 16th channel welded.Electric adjustment of cardboard the size of the lateral output pneumatic control board, electrically adjustable conveyor speed.2.Cardboard sheets to the desired or height requirements will be controlled by a foot switch out of cardboard.3.Vertical bin using wide flat belt conveyor transport.