PTO Shaft For Feed Mixers

PTO Shaft to fit Single Auger Twin Auger and the Total Mix PTO shaft used for Jaylor Vertical Mixers TMR   The device transmits motion in a single direction as the tractor drives the implement. In the stop phase, the tractor PTO shaft is disengaged, and the machine moved. The transmission is cut off.   This device assists in operating machinery that have high-speed inertia due to when the stop phase is in place this tractor's PTO is removed from the machine being driven.   Original Equipment is listed on the left as Size 6, or 8 copy of BYP. )Based on HP   at 60 HP or lower = CAT4 = Size 6. ******* greater than 60 HP = CAT5 = Size 8.   Jaylor provides Constant Velocity shafts or standard PTO   We also supply all components for the feed mixer.   MAINSHAFT CVO: Constant Velocity Category    Series  Tractor Tractors that have 1.375"-6 PTO 4 (60 HP@540 RPM)   S6  1.375-6 5 (90 HP@540 RPM)   S8  1.375-6 Tractors that have 1.375"-21 PTO    4 (60 HP@540 RPM)   S6  1.375-21 5 (90 HP@540 RPM)   S8  1.375-21 Tractors that have 1.750"-20 PTO    4 (60 HP@540 RPM)   S6  1.750-20 5 (90 HP@540 RPM)   S8  1.750-20 Shear Bolt Yokes: Part Number Model   Diameter    No of Splines   C-to-bolt   Bolt    c-e Length    Torque Size 6 Shear Bolt Yokes 6060H3702R  LB  1.375   21  55  M10x50  134 2700nm BTB06215510A    LB  1.375   21  55  M10 4.8 2700nm 6060H0302R  LB  1.375   6   55  M10x50  134 2700nm BTB06385510A    SB  1.375   6   55  M10     2500nm BTB06205510A    SB  1.750   20  55  M10     2500nm BTB06345510A    LB  1.750   6   55  M10 4.8 6060H3802R  LB  1.750   20  55  M10x50  134 2700nm 6060H3707R  LB  1.750   27  55  M10x50      2700nm 6060H0402R  LB  1.750   6   55  M10x50  134 2700nm Size 8 Shear Bolt Yokes 6060M3702R  LB  1.375   21  50mm    M12 143mm   3800nm BTB08215712A    LB  1.375   21      M12 pin QD  3500nm 6060M0302R  LB  1.375   6   50mm    M12 143mm   3800nm 6060M0307R  LB  1.375   6   50mm    M12 143mm   3500nm BTB08385712A    LB  1.375   6       M12 pin QD  3500nm 6060M3802R  LB  1.750   20  50mm    M12 143mm   3800nm BTB08205712A    LB  1.750   20      M12 pin QD  3500nm 6060M3902R  LB  1.750   27      M12     6060M0403R  LB  1.750   6   50mm    M12 143mm   3800nm BTB08345712A    LB  1.750   6       M12 pin QD  3500nm PARTS OF THE PTO SHAFTPTO Shaft for Jaylor Vertical TMR Feed Mixers It's crucial to understand the dimensions, measurement horsepower, dimensions, and other PTO shaft components in order to select the correct PTO shaft that will fit in your equipment. Although the U-joints and yokes are essential for their function however, the safety chains as well as the shield are the most important components that make up the PTO shaft, which will help ensure your safety during operation.   Internal Yoke: There are two of them, situated on both sides of the PTO shaft, namely the implement and the tractor. The welded end is attached onto the drive side. Universal Joint- There are two at each end of the PTO shaft. External Yoke - There are two on both sides on the PTO shaft. It is an "Y" design to connect to the U-joint as well as an opening for females. Safety Chains - The chains anchor the PTO shaft onto the machine and also the tractor. Safety ShieldCones located at both the ends. Size is the most important aspect of the PTO shaft Whatever task you'll use the PTO shaft for it is essential to are using the right dimension. The manufacturer will provide length recommendations to help to get an idea. When measuring the length of a PTO shaft, you can use the tape measure and take measurements from the outside of each yoke in order to get the length closed. The size of the series should be in line to the horsepower that your tractor is equipped with. Two different speeds are employed typically when using tractor PTO shafts, those of 540 (type one) and the 1000 (type three) RPM.