Quick Details
- Processing Time:3-6 months
- Port:Tianjin Port
- Supply Ability: 10 Sets Per Year
- Warranty:1 YEAR
- Processing Type:AUTOMATIC
- Power(W):380V 50Hz
- Place of Origin:CHINA
- Condition:NEW
- Certification:CE,ISO
- Brand Name:YIKE
- After-sales Service Provided:YES
- Brand Name:YIKE
3 PLY
CORRUGATED CARDBOARD PRODUCTION LINE
main technical parameters and requirements in production line
The maximum production width of the corrugated cardboard:1800mm
Design speed:100m/min
Economic speed:60-80m/min
note:Production line speed test paper should meet the following requirements:(the surface temperature of the equipment is not less than
172ºC)
Paper
rating of not less than B grade Paper moisture content of about:11%±2%
top
paper:100-250g/m2 core
paper:100--250g/m2
corrugated
paper:100-200g/m2
Flute-type combination:A ,C, B, E(as customers' requirement)
Steam the necessary requirements:
amount of steam 2500-3000Kg/Hr the highest
pressure:1.2MPa
common
pressure:0.8-1.1MPa
6,power supply:380V 50Hz Three-phase four-wire
system
7,equipment installed total power:about120Kw The actual power consumption:about 60Kw(full speed)
8,equipment covers:about38m×10m×5m(Specific length of foundation Figure prevail)
9,Equipment out of paper orientation:According to the user to determine the transmission plant set left or right position
10,Equipment applicability,Available in A, B, C class domestic or imported paper Paper
Customer-owned section
1,steam heating system:proposal with 2000Kg / Hr
of a steam boiler pressure:1.25MPa steam pipeline.
2,air compressed machine,air pipeline,glue
conveying pipe.
3,power supply,wires connected to the operation
panel and line pipe.
4,water sources,water pipelines,buckets and so
on.
5,Water, electricity, gas flush mounting civil
foundation.
6,Test with the base paper,corn starch
(potato),Industrial use caustic soda,borax and other material.
7,Oil equipment,lubricating oil,hydraulic
oil,lubricating grease.
8,installation,commissioning of food,
accommodation.And provide installers with the installation.
ZJ-F shaftless mill roll stand
Structural features:
1.Symmetrical structure can also install two
bundles of paper at the same time,Paper can be used for non-stop for a job;Adopts mechanical drive to complete the paper clamping, lifting, loosen, move on, around translational motion,
etc.
2.each shaftless mill roll stand is equipped
with two pieces of paper guide, two set of paper car;paper guide the use of channel 14 and the guide post weld,paper car adopt 10mmwelded stell,the length of track is
4500mm.
3.manual dics brake,add screw
following
4.electric elements centralized control the
electric elements,expand chuck.
technical
parameters:
1,Backstands
action mode:mechanical electric operation
2,the range of
paper jams:maximum:1800mm minimum:600mm
3,the diameter
of paper jams:maximum:¢1400mm minimum:¢400mm
4,Unilateral
maximum load:maximum2000Kg
5,Powered motor
parameters:
A Paper jams
motor550W×4set 380V 50HZ short(S2)working standard
B lift motor
1.5Kw 380V 50HZ short(S2)working standard
RG-1-600 top(core)paper preheater
Structural features:
1. In accordance with national standard category pressure vessel,and with the pressure vessel certificate.
2. The roll surface after precision grinding, fine grinding and hard chromium plating processing,surface friction,durable.
3. electric adjustable angle, angle can rotate in the range of 360°,and adjust the paper preheat area.
SF-280S fingerless type single facer
Structural features:
1. adopt hood suction structure,matched high pressure powerful fan. Gas supply and electrical control
cabinet to focus on the same operation, the operating side full cover closed.
2. High quality resin sand casting,wall thickness 200mm。Adopt independent gear box, Universal joint
transmission structure.
3. install the lifting trolley on the conveyor bridge,Need to use the car will tile roll assembly and
pressure roller, such as convenient and quick.
4. Glue roller unit structure with the overall relocation,Maintenance can sway the machine at the overall
maintenance,improve the working efficiency。
5. The humidity control apparatus equipped with a spray, so flute type to maintain good stability of
deformation, avoid dry。
6. Automatic circulation system for glue, two-cylinder pneumatic gluing device, with good cushioning
effect.
RG-2-600 triple preheater
Structural features:
1. preheat
roller accord with the national standard of the pressure vessal,and enclosed the pressure container certificate and inspection certificate.
2. Each roller
surface after grinding precision grinding and dealing with hard chrome plating, Surface friction is small, durable.
3Electric
adjustable angle, it can rotated adjust the paper preheat area in the range of 360°.
GM-12 double glue machine
Structural features:
1. After the
glue roller surface after quenching inner hole machining, grinding and dynamic balancing surface engraved with pit style textured, coating evenly, less consumption of
plastic.
2. doctor
roller surface by grinding and hard chromium plating.
3. other guide
rollers with hard chrome plated.
4. Pressure
roller with pneumatic lift, easy operation.
5. manually
adjust scraping gap.
6. glue roller
¢ 215mm,Doctor roll¢ 122mm,press paper roller¢ 122mm,preheat roller 270mm.
7. Electrical
design, construction production process, follow the national standards, low failure rate, easy maintenance.
SM-10 type double
facer
Structural
features:
1. Heating plate surface by grinding treatment, hot plate width 600mm, a total of 12 heating plate and cooling 4 m.
Heating plate with a container board production, in line with national standards for a class pressure vessel, with pressure vessel certificate and inspection
certificate.
2. Hot plate with intensive gravitational roll structure. Roll adopt pneumatic lifting.
3. Heating plate heat transfer pipe temperature control sub-four-segment, with a temperature display.
4. on cotton use two-cylinder S type cotton belt with the tensioning device.
5. lower belt adopt pneumatic tensioning.
6. Drive roller coated with attached wear-resistant rubber ,showed a herringbone structure,With a high, ensure smooth cardboard
output.
7. Main drive motor for frequency conversion motor,low-speed torque,wide speed range ,reliable, and easy maintenance.
8. hot plate internal for partition isolation structure,s-shaped flow of steam,Steam, water separation function significantly improves the utilization of
steam.
ZQS thin knife slitting
structural feature:
1. Overcome
the conventional type of pole, cutting pressure lines appear when collapsed cardboard cut phenomenon, cutting board smooth, quality has improved
significantly.
2. the whole
machine can remove left and right,cycloid reducer to adjust.
3. Cutter and
easy to adjust the pressure line, the error ± 0.5mm, automatic sharpening device, you can achieve timing Brothers, with intermittent Brothers and other
features.
4. the machine
adopt five knives eight lines,the blade is made of tungsten alloy steel, the using life is not less than 3 million running meters.
NC-120 NC cutter helical
knives
structural
feature:
1 .it can store 200 units orders,replace the cutter specifications quickly and accurately,changing orders without stop,And enables networked computers to facilitate
production management.
2. Knife shaft drive gears are precision forged steel induction hardening, backlash-free transmission, advanced keyless connection, high transmission
accuracy.
3. Cutting machine adopts inlaid front steel blade knife spiral structure, serrated knife. scissors, shears, shear force, long blade
life.
4. around feed rollers are used the sun gear platen way, smooth delivery, pressure evenly, easy to crush plate board or cause
blockage.
5. Exact and adjustable no gap gear to ensure precise blade engagement, running balance.
6. Knife roller: fine quality forged steel material, the balanced, with good stability.
7. Germany Bryant servo motor drive controller, Taiwan Eview yield 10.4 inches color touch screen display, the project at a
glance.
8. Cutting length: 500mm-9000mm, cutting precision: ± 1mm (at steady speed).
DMT-120 paper sheet delivery and side
conveyor
structural features:
1.Adopted on
the 16th channel welded.Electric adjustment of cardboard the size of the lateral output pneumatic control board, electrically adjustable conveyor
speed.
2.Cardboard
sheets to the desired number or height requirements will be controlled by a foot switch out of cardboard.
3.Vertical bin
using wide flat belt conveyor transport.